This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:arduino_module_setting [2020/01/20 12:28] golikov created |
en:arduino_module_setting [2020/03/25 16:28] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====Установка ПО==== | + | ====== Preparing for Work ====== |
- | * [[https://www.arduino.cc/en/Main/Software|Скачайте]] и установите среду разработки Arduino IDE на свой компьютер | + | |
- | * Убедитесь, что на вашем компьютере имеется nактуальное [[http://orbicraft.sputnix.ru/doku.php?id=software|программное обеспечение]] для работы с конструктором: | + | |
- | * NotePad ++ | + | |
- | * Библиотека Libschsat_Ard | + | |
- | * Библиотека для взаимодействия конструктора ОрбиКрафт и Arduino | + | |
- | * [[https://www.arduino.cc/en/guide/libraries|Установите]] библиотеку для взаимодействия Arduino и конструктора ОрбиКрафт в Arduino IDE | + | |
+ | ====Installing Software==== | ||
+ | * [[https://www.arduino.cc/en/Main/Software|Download]] the Arduino IDE and install it on your computer. | ||
+ | * Make sure your computer has [[http://orbicraft.sputnix.ru/doku.php?id=software|up-to-date software]] for the construction set: | ||
+ | * NotePad ++ | ||
+ | * The Libschsat_Ard library | ||
+ | * The library for interaction between Orbicraft Construction Set and Arduino | ||
+ | * [[https://www.arduino.cc/en/guide/libraries|Install]] the library for interaction between Arduino and the Orbicraft Construction Set in Arduino IDE. | ||
- | ====Подключение==== | + | ====Connecting==== |
- | * Установите шилд на Arduino Mega 2560 | + | * Install the shield in Arduino Mega 2560 |
- | * Подключите шилд в сеть конструктора ОрбиКрафт через стандартный шлейф | + | * Connect the shield to the Orbicraft Construction Set network using a standard ribbon cable |
<note important> | <note important> | ||
- | Питание Arduino осуществляется через пин Vin из шины конструктора через шилд. На представленном примере красный светодиод показывает, что пришло питание с шины конструктора на шилд, а зеленый, что Arduino, в свою очередь, дает 5В для питания подключенной полезной нагрузки с шилда. Оба светодиода должны гореть постоянно. Цвет может отличаться в зависимости от поставки. | + | Power will be supplied to Arduino from the construction set bus using the Vin pin via the shield. In the example shown below the red LED indicates power coming from the construction set bus to the shield and the red LED shows that Arduino in turn outputs 5 VDC to power up the connected payload from the shield. Both LEDs must be lit continuously. Color may vary depending on the version supplied. |
</note> | </note> | ||
- | {{ ard_2.png?direct&1000 | Подключение Arduino к ОрбиКрафту}} | + | {{:en:arduino_01.png?900|}} |
- | * Подключите Arduino Mega 2560 к персональному компьютеру стандартным кабелем USB Type B | + | * Connect Arduino Mega 2560 to the PC using a standard USB Type B cable. |
- | {{ ard_2173_1.jpg?direct&500 | Подключение Arduino к персональному компьютеру}} | + | {{:en:arduino_02.png?600|}} |
- | * Далее мы переходим к разделу [[http://orbicraft.sputnix.ru/doku.php?id=arduino_module_base_lesson|начало работы]], в котором рассказывается о взаимодействии Arduino и конструктора ОрбиКрафт. | + | * Next, proceed to the Getting Started section to explain interoperation between Arduino and the Orbicraft construction set. |